How to remove and reinstall a hood latch assembly and Hood Cable on Acura MDX?

Scribe a line around the latch to aid alignment when reinstalling the latch assembly. Remove the latch retaining bolts securing the latch to the radiator support and remove the latch. Disconnect the hood cable by disengaging the cable from the back of the latch assembly. Installation is the reverse of the removal procedure. Adjust the latch so the hood engages securely when closed and the hood bumpers are slightly compressed. Remove the hood latch, then detach the cable from the latch. Remove the left-side inner fender splash shield. Attach a length of wire to the end of the cable (in the engine compartment). This will be used to pull the new cable back into the engine compartment. Working in the engine compartment, detach the cable from all of its retaining clips. It may be necessary to cut some of the clips to free the cable. Working under the instrument panel, remove the left-side kick panel (Remove the fastener, then detach the kick panel). Remove the screws and detach the hood release handle. Dislodge the grommet and pull the cable through the firewall and into the cab. Detach the wire from the old cable, then attach it to the end of the new cable. Make sure the new cable is equipped with a grommet. Pull the new cable through the firewall and into the engine compartment. Seat the grommet in the firewall. The remainder of installation is the reverse of removal.

Genuine Acura MDX Hood Cable

Hood Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Hood Cables found

View related parts
Acura MDX Hood-Release Cable
Part Number: 74130-STX-A00
$13.49 MSRP: $18.82
You Save: $5.33 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire Assembly, Hood; Release Cable
- Warranty: This genuine part is guaranteed by Acura's factory warranty.
View related parts
Acura MDX Wire Assembly , Front Hood
Part Number: 74131-TYA-A01
$12.80 MSRP: $17.85
You Save: $5.05 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Cable
- Position: Front
- Warranty: This genuine part is guaranteed by Acura's factory warranty.
View related parts
Acura MDX Hood Wire Assembly
Part Number: 74130-TZ5-A00
$13.18 MSRP: $18.38
You Save: $5.20 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire Assembly, Hood ; Release Cable; Release Cable
- Warranty: This genuine part is guaranteed by Acura's factory warranty.
View related parts
Acura MDX Hood Wire Assembly
Part Number: 74130-TZ5-A01
$20.33 MSRP: $28.35
You Save: $8.02 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire Assembly, Hood ; Release Cable; Release Cable
- Warranty: This genuine part is guaranteed by Acura's factory warranty.
View related parts
Acura MDX Hood Wire Assembly
Part Number: 74130-S3V-A00
$12.09 MSRP: $15.78
You Save: $3.69 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wire Assembly, Hood ; Release Cable; Release Cable
- Warranty: This genuine part is guaranteed by Acura's factory warranty.
View related parts
Acura MDX Wire Assembly , Rear Hood
Part Number: 74132-TYA-A01
$11.27 MSRP: $15.72
You Save: $4.45 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Release Cable
- Position: Rear
- Warranty: This genuine part is guaranteed by Acura's factory warranty.
View related parts
Acura MDX Remote Wire, Hood
Part Number: 74140-TYA-A01
$3.11 MSRP: $4.34
You Save: $1.23 (29%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Lock Cable
- Warranty: This genuine part is guaranteed by Acura's factory warranty.
View related parts
Acura MDX Hood Release Cable Wire Assembly
Part Number: 74130-S3V-A01
$12.86 MSRP: $17.93
You Save: $5.07 (29%)
Product Specifications
- Other Name: Wire Assembly, Hood; Release Cable
- Warranty: This genuine part is guaranteed by Acura's factory warranty.

Acura MDX Hood Cable

The Acura MDX Hood Cable lets drivers pop the hood with a quick pull of the cabin lever, giving fast access for oil checks, coolant top ups, or bigger repairs. Running from the dash mounted release handle to a junction near the grille, the Hood Cable then branches to latches on each side, tugging them open the moment tension is applied. Over the years the SUV has relied on a two piece Hood Cable set, one primary line that links lever to junction and two shorter secondary lines that link junction to the dual latches, an arrangement chosen to ensure even, simultaneous release. Earlier Acura MDX editions applied steel wound strands surrounded by simple plastic sheathing, while later versions adopted improved corrosion resistant casings that seal out road moisture, yet both styles work through the same pull and latch principle. When age or flexing causes fraying, stretching, or cracks, the Hood Cable can stick, leaving the hood locked tight and proving why routine checks matter. Replacing a fatigued line with a fresh OEM unit restores smooth lever feel, keeps the iconic Acura SUV serviceable in the driveway, and preserves the dependable front opening action that every MDX owner expects from this small but vital Hood Cable.

We provide a broad range of OEM Acura MDX Hood Cable at unbeatable prices on our website. For your OEM parts, You can count on the guaranteed quality, manufacturer's warranty, outstanding customer service, and prompt delivery. We look forward to your visit.

Acura MDX Hood Cable Parts Questions & Experts Answers

Hood-Release Cable
74130-STX-A00
Q: How to remove and reinstall a hood latch assembly and Hood Cable on Acura MDX?
A:
Scribe a line around the latch to aid alignment when reinstalling the latch assembly. Remove the latch retaining bolts securing the latch to the radiator support and remove the latch. Disconnect the hood cable by disengaging the cable from the back of the latch assembly. Installation is the reverse of the removal procedure. Adjust the latch so the hood engages securely when closed and the hood bumpers are slightly compressed. Remove the hood latch, then detach the cable from the latch. Remove the left-side inner fender splash shield. Attach a length of wire to the end of the cable (in the engine compartment). This will be used to pull the new cable back into the engine compartment. Working in the engine compartment, detach the cable from all of its retaining clips. It may be necessary to cut some of the clips to free the cable. Working under the instrument panel, remove the left-side kick panel (Remove the fastener, then detach the kick panel). Remove the screws and detach the hood release handle. Dislodge the grommet and pull the cable through the firewall and into the cab. Detach the wire from the old cable, then attach it to the end of the new cable. Make sure the new cable is equipped with a grommet. Pull the new cable through the firewall and into the engine compartment. Seat the grommet in the firewall. The remainder of installation is the reverse of removal.