Question 1

How to Detach the Fuel Pump from the Fuel Tank and Ensure Proper Installation on Acura Integra?

Accepted Answer

Detach the cable from the negative battery terminal, ensuring you have the correct activation code for the stereo's anti-theft system before disconnecting the battery. Relieve the fuel system pressure. For all models except the 1998 Integra hatchbacks, remove the rear seat; for the 1998 Integra hatchbacks, remove the spare tire cover and protective cover. Remove the bolts retaining the fuel pump access cover, then unplug the electrical connector from the fuel pump and detach the fuel lines. Remove the retaining nuts for the fuel pump assembly and lift the pump from the tank, angling it slightly to avoid damaging the pump screen. Take off the electrical connector protective cover and disconnect the electrical connector from the fuel pump by lifting the tab. Squeeze the hose clamps with pliers, removing the upper clamp from the hose and sliding the lower clamp halfway up the hose off the fuel pump inlet. Separate the pump from the fuel pump bracket and remove the sock filter from the end of the pump by prying off the retaining clip. Installation is the reverse of removal, ensuring to replace sealing washers if the fuel line has a banjo bolt fitting, obtain a new plastic retainer for models with a quick-connect fitting, and install a new gasket on the cover plate flange.

Question 2

How to check the fuel pump and inspect fuel lines for issues related to insufficient fuel delivery on an Acura Legend?

Accepted Answer

To check for limited fuel supply start by examining all fuel lines to rule out line leaks. Turn on the ignition with the parking brake set and an assistant present to check the fuel pump sound during the operation on Legend models. A quick whirring noise needs to occur briefly before it intensifies when the engine starts. The deficiency of the whirring sound indicates that a wiring issue exists in either the fuel pump circuit or the fuel main relay circuit. Relieving fuel pressure requires the service bolt on top of the fuel filter while installing a special adapter onto your fuel pressure gauge. Start the engine then disconnect the vacuum hose from the pressure regulator before you check the fuel pressure measurement. The fuel pressure needs evaluation to verify a working fuel regulator while identifying blockages or pinches in return fuel lines if pressure exceeds specifications. To check low fuel pressure examine the fuel filter followed by inspecting for pinched or clogged fuel hoses and analyzing the pressure regulator for faults and searching for fuel line leaks. Proceed to examine the fuel pump when no issues exist with the other components. If you hear brief whirring noise when an assistant turns the ignition switch to On position, it confirms the pump is working correctly. Examine the fuel pump connector that sits above the fuel tank in the luggage area before checking with a voltmeter by touching the positive probe to the black/yellow wire then the negative probe to the black wire while enabling the ignition switch to verify voltage availability. Check the main relay first while inspecting the fuel pump only when voltage is detected. Check the main relay by extracting it from the under-dash fuse panel area. Add battery voltage power to terminal no. 4 while applying ground to no. 8 terminal to test for continuous electricity flow between no. 5 and no. 7 terminals. The relay should be replaced when continuity is absent. The tester should verify that the no. 1 connects with no. 3 when grounding no. 2 while applying battery voltage to no. 5; if there is no connection, the user must replace the relay. At the end connect battery voltage to the no. 3 relay terminal following the ground of no. 8 terminal before checking for continuity between no. 5 and no. 7 terminals; if there is no continuity the relay needs replacement.

Question 3

How to replace a fuel pump/Fuel Filter/fuel level sending unit module in Acura MDX?

Accepted Answer

Release fuel pressure and disconnect the battery. Remove the fuel pump/fuel level sending unit from the tank. For 2001-2004 Acura and Honda models: Disconnect hoses, electrical connectors, and separate the bracket and case. Remove the pump retainer, rubber isolator, fuel pump, and fuel inlet "sock". Remove the fuel level sending unit. Clean the fuel strainer in solvent or replace if necessary. Check the condition of the O-rings and replace if needed. Ensure the spacer is in place. Reassemble and check for leaks. For 2003 and later Acura and 2005 and later Honda models: Disconnect the electrical connector and remove the case. Disconnect the fuel supply line fitting and remove the O-ring. Disconnect the electrical connectors and remove the fuel pressure regulator housing. Remove the fuel pressure regulator and O-rings. Inspect the spacer and mesh filter screen, replace if damaged. Remove the fuel pump and O-ring. Remove the suction filter. Clean the fuel strainer in solvent or replace if necessary. Reassemble with new O-rings and retainer clip. Check for leaks after reassembly.

Genuine Acura Fuel Pump

103 Fuel Pumps found

Acura Fuel Pump Module Assembly

Acura Fuel Pump Module Set

Acura Fuel Pump Set

Acura Gas Fuel Tank Pump

Acura Fuel Pump Module Assembly

Acura Fuel High Pressure Pump Assembly

Acura Fuel High Pressure Pump Assembly

Acura Fuel Pump Module Set

Acura Fuel Pump Module Set

Acura Fuel Pump Module Set

Acura Fuel Pump Module Assembly

Acura Fuel Pump Module Assembly

Acura Fuel Pump Module Set

Acura Fuel Module Set (Sub)

Acura Fuel Pump Set

Acura Fuel Pump Module Set

Acura Fuel Pump Module Assembly

Acura Fuel Pump Assembly

Acura Fuel Pump Module Assembly

Acura Fuel Pump Assembly

About Acura Fuel Pump

Acura Fuel Pump Parts Questions & Experts Answers

Related Acura Parts

Browse by Model